Ardex EG 15 Epoxy Grout – Part C (Colour Pack)

Ardex EG 15 Epoxy Grout is an easy-clean, high-performance Epoxy Grout.
Use where strict hygiene standards, high chemical and physical resistance are required
Exceptionally easy clean off
Solvent free, environmentally friendly
For joints from 1.5mm to 15mm
Suitable for wall and floor applications
Adjustable viscosity to suit application conditions
Use with range of Ardex Colour Packs
Water wash up, easier than other epoxy grouts
Ideal for wet areas including swimming and hydrotherapy pools For internal and external applications
Low VOC content

DESCRIPTION

Ardex EG 15 Epoxy Grout is a high performance epoxy grout designed for situations that require strict standards of hygiene, high chemical and physical resistance. Ardex EG 15 Epoxy Grout is exceptionally easy to clean up during application. It can be used in joints up to 15mm wide on walls and floors.

FOR GROUTING (TILE TYPES)

All ceramic tiles, porcelain and natural stone.
Note: porous, moisture sensitive and textured tiles may require special application procedures, contact Ardex Technical Services.

PREPARATION

Ensure joints are clean and free from dust, excess adhesive and bedding mortar. Do not grout until the adhesive has set firmly. All ‘spacers’ must be removed from joints. Joints must be dry before grouting and free from permanent dampness.
Prior to grouting, it is advisable to check ease of cleaning with tiles that have a textured or matt surface.

MIXING RATIO

ARDEX EG 15 Epoxy Grout should be mixed to the ratios below in parts per volume:

Part A Compound.          2 parts/1L
Part B Hardener Part.     1 part/500mL
Part C Colour Pack.       5-7 parts/5kg

CLEANING

For best results, cleaning should be completed within 15 minutes after application. Grouting and cleaning 1-2m2 at a time is recommended. Consult Ardex for porous and heavily textured tiles.

Step 1: Remove excess grout from the tile surface using a rubber grout float in a diagonal pattern.
Step 2: Using a damp cleaning cloth, gently wipe in a circular motion and loosen the excess grout on the tile surface. Frequently clean cloth in water.
Step 3: Using a damp clean cloth, gently remove any further residue and smooth grout surface.
Frequent rinsing of the cleaning cloth reduces clogging and prolongs its life.
Step 4: Using a chamois, remove any remaining haze from the surface.

It is important to clean all grout from the tile surface before the grout hardens. The initial cleaning can become very difficult to wash outside of the material’s pot life. In some cases a slight smear may develop on the tile surface after cleaning. The smear can be removed 2-4 hours after grout application by wiping with a clean sponge or open weave damp cloth. For stubborn areas use a scourer. Clean residue no later than 24 hours after grout application.

DRYING TIME

Open to light traffic after 24 hours, full cure and stain resistance after approximately 7 days, after which time the grout joints are chemically resistant, at 23°C and 50% relative humidity. Allow longer for lower temperatures.

PACKAGING

ARDEX EG 15 Epoxy Grout is a three part system.
Part A: 1L
Part B: 500mL
Part C – Ardex Colour Pack 5kg

SHELF LIFE

Ardex EG 15 Epoxy Grout has a shelf life of 24 months, when stored in the original unopened packaging, in a dry place at 23ºC and 50% relative humidity.
Keep away from flames and high temperatures.
Keep away from food and drink.
Reseal partly used containers.

PAY ATTENTION TO THE FOLLOWING:

Epoxy based grouts are prone to discolouration and chalking when used externally. However, performance is not affected. Epoxy grouts are subject to colour variation over prolonged periods.
Discolouration can occur if too much water is used during clean up.
Exercise caution when grouting over soft or highly glazed tiles, Ardex recommend a trial application with all tiles before installation.
In low temperatures, it is advisable to pre-heat the separate components or store in a temperature controlled environment for 12 hours prior to use. The sealed liquid components can be heated in warm water of up to 25°C.
In high temperatures, the material should be stored in shade or an air conditioned environment for 12 hours prior to use.
Ardex EG 15 Epoxy Grout has very good chemical resistance but is not recommended for use in direct contact with commercial deep fryers, Ardex provides other systems.
Ardex EG 15 Epoxy Grout is water resistant, but is not intended to waterproof surfaces and does not replace a correctly installed waterproof membrane under tiles.
Light foot traffic is permitted after 24 hours at 23°C and 50% relative humidity but full stain and chemical resistance is not achieved until full cure after 7 days at 23°C and 50% relative humidity.

SAFETY DATA

This product causes severe skin burns and eye damage.
Harmful if swallowed and in contact with skin.
May cause an allergic skin reaction.
Harmful if inhaled.
May cause drowsiness or dizziness.
Suspected of causing cancer.
May be corrosive to metals.
Harmful to aquatic life with
long lasting effects. Please obtain special instructions
before use.
Wear protective gloves, clothing, eye and face protection.
Avoid inhaling dust/fumes/gas/mist/vapours/ spray.
Ensure adequate ventilation during mixing and application.
IF SWALLOWED: rinse mouth. Do not induce vomiting.
IF ON SKIN (or hair): remove/take off immediately all contaminated clothing. Rinse skin with water/shower.
In case of contact with the EYES rinse with running water until advised to stop by the Poisons Information Centre or a doctor, or for at least 15 minutes.
Store locked up.
Check with your local Council regarding the disposal of contents and packaging.
KEEP OUT OF THE REACH OF CHILDREN
Call the Poisons Information Centre on 131 126 (AUS) and 0800 764 766 (NZ) or call a doctor if you feel unwell. Additional information is in the Safety Data Sheet (SDS) at www.ardexaustralia.com.
Ardex EG 15 Part A is considered a Dangerous Good, Miscellaneous, Class 9.
Ardex EG 15 Part B is considered a Dangerous Goods, Corrosive, Class 8.